![]() ![]() (For the memory feature to function, the transformer needs to be in this mode for at least 24 hours). 【Memory Function】 You won't need to alter the low voltage transformer too often because it will stay in the setting you chose earlier even when there is a power loss. It has Built-in mounting holes, 3.3-foot STJW 18AWG power cord, and direct wall mounting for outdoor walls. ![]() 【Easy to Operate and Install】 To select Always On, Auto, or Countdown Timing mode, press up/down arrow. With this option, the transformer will turn on at dusk and shut off automatically 1/2/3/4/5/6/7/8/9 hours later. 【Countdown Timer】 Light control timing has 1-9-hour countdown. By converting household voltage from 120V AC to 12V AC safety voltage using 120W, a safer and more useful electrical current level is produced. 【Built-in Dusk to Dawn Sensor】Landscape lighting that is connected to this transformer will automatically switch on at dusk and off at dawn. Please refer to this following cable slection chart, it will help you with it. What Cable and How Long should I use to connect with transformer? Then you can choose the transformer higher than 113W(=91W/0.8). Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.1.Calculate the total wattage of your light fixtures in your plan.Ģ.Choose the transformer that is large enough to support the total wattage you need.ģ.The transformer wattage load (total watts needed for your fixtures) should be within 80% of the rated capacity of the transformer.įor example: if you have 7 pack 13W landscape lights, so the total wattage is 91W. The LED next to the programmed mode will illuminate. To view the program that is currently set when the timer is not providing power to the attached devices, press the "SET" button.The LED next to the programmed mode will glow red when the timer programming is activated and power is being provided to attached devices.When set to "ON", the timer will provide continual power to attached devices until the timer is switched to "OFF", or to any of the other Operating Modes. ![]() Headlights, porch lights, street lamps and other external lighting sources will not interfere with the active timer program. Once programming activates at dusk in the 2hr, 4hr, 6hr, 8hr, 12hr or dusk-to-dawn mode, the program cycle will complete before the timer resets.The photocell is located above the "SET" button on the face of the timer. This timer operates using a light-sensitive photocell that senses when the environment is getting dark (dusk) or light (dawn).The timer will function outdoors when installed and operated as outlined in this manual. This timer is weather-resistant and rated for Outdoor Use.Plug the devices into the outlets on the bottom of the timer. After 5 seconds, LED will flash rapidly to confirm selection.Ģ Hrs - Power will turn on at dusk and remain on for 2 hoursĤ Hrs - Power will turn on at dusk and remain on for 4 hoursĦ Hrs - Power will turn on at dusk and remain on for 6 hoursĨ Hrs - Power will turn on at dusk and remain on for 8 hoursġ2 Hrs - Power will turn on at dusk and remain on for 12 hoursĭusk-Dawn - Power will turn on at dusk and remain on until dawn Press the "SET" button to cycle the LED's to the desired mode. Do not use extension cords to connect the timer to the power source. Use an outdoor-rated three-pronged grounded electrical outlet. Place the timer over the screw heads and push down to lock into place.Insert two #6 sheet metal screws (not included), leaving screw heads protruding 1/8 inch from the surface.Drill two 3/32 inch pilot holes where indicated on the mounting template.Temporarily secure the mounting template to the flat surface where the timer is to be mounted.Create a mounting template by placing a sheet of paper over the back of the timer and punching holes through the paper where the mounting holes are located on the timer.For a more secure mounting, use the two MOUNTING HOLES on the back of the timer.Using a screw or hook (not included), secure the MOUNTING TAB at the top of the timer to a wall or post.INSTALL TIMER to a vertical a flat surface close to a properly installed outdoor-rated grounded receptacle. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |